POCO X5 Pro 5G (Redwood) Test Point

The POCO X5 Pro 5G (Redwood) is one of Xiaomi's mid-range devices known for its exceptional performance and features. However, if your device faces issues like bootloops, FRP lock, or becomes unresponsive, you can access EDL Mode (Emergency Download Mode) using the Test Point method.

In this guide, we will walk you through the process of locating the POCO X5 Pro 5G Test Point, entering EDL Mode, and resolving common issues.

What is the EDL Test Point?

The EDL Test Point is a designated area on the motherboard of your phone that, when shorted, forces the device into Emergency Download Mode. This mode is essential for:

• Flashing firmware to unbrick the device.
• Resolving bootloader issues.
• Bypassing FRP (Factory Reset Protection) lock.

For the POCO X5 Pro 5G, also known as Redwood, this Test Point can be found on the motherboard of the following variants:

• 22101320G
• 22101320I

Why Use the Test Point Method?

The EDL Point POCO X5 Pro 5G Test Point is used when:

1. The device is hard-bricked or stuck in a bootloop.
2. The phone isn’t detected in Fastboot or Recovery Mode.
3. You need to bypass FRP locks or flash stock firmware.
4. The device is unresponsive to standard troubleshooting methods.

Requirements to Access EDL Mode

Tools You’ll Need:

1. POCO X5 Pro 5G (Redwood): Models 22101320G or 22101320I.
2. A precision screwdriver to open the device.
3. Tweezers or a conductive tool to short the Test Points.
4. A USB cable and a PC with Qualcomm drivers installed.
5. Flashing tools such as Mi Flash Tool or QFIL.
6. Stock firmware for your specific model.

Steps to Access EDL Point POCO X5 Pro 5G Test Point

1. Power Off Your Phone

• If the device is unresponsive, press and hold the power button until it shuts down.

2. Open the Device Back Cover

• Use a plastic prying tool to gently remove the back cover.
• Unscrew the protective shield over the motherboard.

3. Locate the Test Points

• The EDL Point redwood Test Point is located near the battery connector on the motherboard.
• These Test Points are specific to the POCO X5 Pro 5G (models 22101320G and 22101320I).
• Refer to the image below for the exact location (Insert Picture Here).

4. Short the Test Points

• Use tweezers or a conductive tool to short the Test Points.
• While keeping them shorted, connect the phone to your PC using a USB cable.

5. Check for EDL Mode

• Open Device Manager on your PC and verify if the phone is detected as Qualcomm HS-USB QDLoader 9008.

6. Flash Firmware or Perform Repairs

• Use a flashing tool like Mi Flash Tool or QFIL to install the stock ROM, remove FRP locks, or fix other software issues.

Important Tips

1. Ensure the Correct Firmware
   Always download and use the firmware that matches your specific variant (22101320G or 22101320I).

2. Handle with Care
   Be cautious while opening the phone and working on the motherboard to avoid damaging internal components.

3. Battery Precaution
   Ensure your phone’s battery is charged to at least 50% before starting the process.

4. Driver Installation
   Install Qualcomm USB drivers on your PC to ensure the phone is properly detected in EDL Mode.

Topic Covered:

1. EDL Point POCO X5 Pro 5G Test Point
2. EDL Point redwood Test Point
3. EDL Point 22101320G Test Point
4. EDL Point 22101320I Test Point

Conclusion

The EDL Point POCO X5 Pro 5G Test Point provides a reliable solution to unbrick your phone, flash firmware, or bypass FRP locks. By following the steps outlined in this guide, you can safely and effectively bring your POCO X5 Pro 5G (Redwood) back to life.

Ensure you follow the instructions carefully, use the correct tools, and handle the hardware gently. With this guide and the accompanying images, accessing the Test Point and entering EDL Mode should be a hassle-free experience.